Leave it to the innovators at Corbin to build a seat as versatile as the four-stroke thumper itself. Our Dual Sport design combines the functionality of a motocross seat with the comfort of Corbin's ergonomic design. Works great for dirt riding, trail riding, dual sport riding, or for your Super Motard setup. Naturally, the styling is all Corbin with a variety of custom options included.

Like all Corbin designs, we start by crafting a seat using our high-density Comfort Cell foam. Comfort Cell retains resiliency and doesn't crush down like the stock foam so we can build a lower seating platform. This gives you better ground reach and a lower center of gravity. For the off-road enthusiast we were sure to leave enough nose to allow you to slide up the tank and get through the corners faster. Or slide back to skim the front end over the whoops.

Now let's say you're on a Dual Sport ride and you've just finished taming some intense terrain... you have some paved miles ahead to catch your breath. Slide towards the rear of the seat and you'll find a wider sculpted bucket shape. This area of the seat gives you more square inches of body contact and the firm support you need for amazing comfort. By the time you hit the next leg of rough stuff you'll be well rested and ready for more.

As you're seated, the bones in your posterior that take most of your body weight are roughly seven inches apart. Strangely enough, this is true for most adults (I'm not making this up!) Your stock seat at its widest point is 6.5". This actually makes the foam of the stock seat crush in and applies pressure to the center of your body. The Corbin model is a full 9.5" and is built with denser, sculpted foam that supports your body weight over a greater area and equalizes pressure. If you consider actual seating surface, the Corbin model gives you almost 300% more body contact! Long story short, greater riding comfort!

On the top, we cover it with only the highest grade of weather resistant materials for durability and long life. To add a bit of flair, we are now offering an embossed material in a variety of colors that gives the look of Carbon Fiber. The one shown on this page used our Blue Carbon-Fiber vinyl and we also offer black, silver (shown in side panels) and green to match your KLX. The traditional Corbin tag has been replaced with a tasteful Corbin logo stitched right into the contrasting side panel. Installation is simple and just like stock.
Specs




Unique Technology

The design and manufacture of Corbin products is so unique that Mike Corbin himself holds more than 60 United States Patents! From the process itself to new innovations like the Corbin Glovebox, you can count on highly functional and unique products that work. Corbin products are manufactured under one or more of the following US Patents: 6,848,156 B2; 6,729,516 B2; D 489,540S; 6,655,740 B1; 6,422,648 B1; 5,544,937; 5,608,957; 4,953,911; D545,073S & 6,971,714 B1.




Fibertech™ Basepan

A purpose built, hybrid material that provides a firm foundation to support the carefully designed ergonomics of the Corbin saddle. Provides a precision fit to every arc and contour of the machine and rides on rubber bumpers to protect your paint. We always design our basepans as flat as possible so bumps or odd shapes don't telegraph through the foam to your body. Click on the button at left to learn more...




Comfort Cell® Foam

The heart of the Corbin saddle! Our exclusive, purpose built foam material, called Comfort Cell, was created to provide a firm, resilient ride that doesn't break down. This means it will support you for long days on the road. Over time, Comfort Cell will break in to provide a personalized fit to your posture and even greater comfort!




Ergonomic Shaping

A major part of the design criteria of the Corbin saddle is the Ergonomic shape. This means the saddle's foam shape is designed to emulate the curves of the human body. This provides more square inches of body contact and helps to eliminate hot spots. This shaping also neutralizes the seating platform to help curb sliding in the saddle which reduces fatigue. In a nutshell... more comfort for a longer ride! Just click the button at left for an animation that shows how it works.




Patented Manufacturing Technology

Always an innovator, Mike Corbin invented Integrated Molding technology which is now the process by which all Corbin saddles are made. This process allows extremely tight tolerances and creates a chemical bond between the foam and base material. To see what this is all about, just click the button for More Info

Accessories


Conditioner


Take good care of your new seat and the seat will take good care of you. Designed to help your leather saddle remain weather resistant and keeps the hide supple. This will allow the leather to break in and age gracefully. Great for boots, gloves & jackets too. Simple rub-in, buff out application. 
*More Info*


Apparel

We're often asked about tees and such so we caved in and had some Corbin gear made up. This is where you'll *Find It*


Ready for a Corbin seat inside your house? Auto styled couches and our classic chrome and leather barstools are a big hit for the man cave!
Check 'em Out *

Notes

Measurements

Seating: 9.5" wide X 29" long
Approx seat height: 33.5"

Installation

Corbin's saddle installs on your bike like stock with two tabs in the front and rear hold down brackets. Come's completely pre-assembled and ready to mount on your bike.




Corbin's saddle DOES work with the Suzuki OEM accessory rear rack. The rear mounting arms need to be slightly spread by hand when fitting the seat. It's snug, but not much trouble.




Corbin saddles (with very few exceptions) include Genuine Leather Seating to provide a luxurious look and feel.... don't let anybody tell you that vinyl is just as good! You wouldn't buy vinyl boots would you?

WARNING: Heater elements (when available) should never be installed in motorcycle seats that will be used by riders that cannot sense heat. This could create a hazardous condition.
Warranty
Please Note Corbin products are designed to fit very close to your bike for a clean look. Due to this, other accessories or options can inhibit proper fit. As an example: Tank Consoles (dashes), ignition modules, exhaust systems, sissy bars, etc. If you have accessories installed on your bike, please let us know so we can verify the fit for you.
Saddle Warranty Basepan, foam and hardware of the Corbin saddle is warranted to the original owner for life. Cover materials, Heaters and workmanship are warranted for one year. Product will only be authorized to be shipped back, freight pre-paid, for refining of shape or to replace/rectify defective parts. In cases where the rework requires a new cover, a recover charge will be applied. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization number (RMA).
Fiberglass Warranty Structural integrity of Corbin fiberglass components are warranted to the original owner for life. Finish and paint are warranted against manufacturing defect for one year. Damage to product and / or painted surfaces from outside forces or misuse is specifically not covered under warranty. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization (RMA) number. A note about paint color matching, Please Read
Export Sales USA pricing shown. When products are shipped throughout the world, you will see higher prices because of freight, customs, duty & applicable taxes. Please consider these costs when purchasing Corbin products outside the USA. If ordering direct from Corbin, we will compute freight charges and add them to the order. BUYER will be responsible for customs, taxes, duty or other charges.
Testimonials

Comments
Of course we want to hear from you! Have some suggestions for us or maybe comments for other riders, send them via THIS FORM.

Submit Photos:
Showcase your bike on Corbin.Com! Use this form to upload photos for possible inclusion on our website. Ready, set... LET'S SEE 'EM!

General Contacts
Corbin Europe
891 Christchurch Road
Bournemouth
Dorset
BH7 6AU
Telephone: +44 (01) 202 797254
email: sales@corbin-europe.com
There are no albums to display product

Dual Sport for Suzuki DR-Z400, DR-Z400 E (all years) `06 - `11 DR-Z400 SM & Kawasaki KLX400

  • Brand: Corbin
  • Product Code: S-DRZ-400-S
  • Availability: In Stock

Available Options

#S-DRZ-400-S - Dual Sport Saddle
£433.00

Related Products

Saddle Cream

Saddle Cream

To assure many years and untold miles of faithful service, be sure to care for your leather saddle w..

Thumbscrews

Thumbscrews

The seat-tab thumbscrew makes installing and removing your saddle a snap. NEW single piece..

Ballcap

Ballcap

A Corbin hat is the best solution for your helmet-hair problem! Adjustable back style in medium heig..

Tags: Dual Sport for Suzuki DR-Z400, DR-Z400 E (all years) `06 - `11 DR-Z400 SM & Kawasaki KLX400

Fibertech Basepan Fiberglass Warranty HD-FLH-9-PAD Ergonomic Shaping trunxbox Sissybar Pads 224 hd-box-1h Electric Heat HD-FLH-9-ARM Backrest System Integrated Molding Genuine leather Key lock installation streamliner1 RK-PAD Rumble Seat streamliner1 Color Matching Honda CRF250L Sissybar Pads 225 Sissybar Pads 210 hd-box