Dual Sport saddle for 2012 - 2016 KTM 250, 300, 350, 450 & 500 XC models

Dual Sport saddle for 2012 - 2016 KTM 250, 300, 350, 450 & 500 XC models

Help & Info




- Select the checkbox next to all parts you would like added to your cart. Please be sure to select your cover options, if applicable, before clicking the "Add To Cart" button.


- If you would like any further help or have any questions please either email or call


- Click for Configurator Help

Saddle Cream®

  • Take good care of your new seat and the seat will take good care of you. Designed to help your leather saddle remain weather resistant and keeps the hide supple. This will allow the leather to break in and age gracefully. Great for boots, gloves & jackets too. Simple rub-in, buff out application.
    * More Info *


Tees, Hats & More

  • We're often asked about tees and such so we caved in and had some Corbin gear made up. This is where you'll * Find It *


Barstools & Auto Furniture

  • Ready for a Corbin seat inside your house? Auto styled couches and our classic chrome and leather barstools are a big hit for the man cave!
    * Check 'em Out *

  • Rider seating: 9.5" wide x 29" long
  • Approx seat height: 37.25" UN-Loaded (500 EXC measured)

  • Installs like stock with a tongue in the front and a single bolt into the saddle from under the fender.

  • Two distinct seats are available, one for the stock tank and one for the Acerbis 20 liter (5.3 gallon) fuel tank. The specific part numbers for the Acerbis tanks we used in tooling are: #2250340001 (black) and #2250340147 (natural).

  • Fits the following 2012-2013models:
    250 XC, 250 XC-F, 250 XC-W, 250 XCF-W, 300 XC, 300 XC-W, 350 XC-F, 350 EXC-F, 350 EXF-W, 450 XC-F, 450 XC-W, 500 EXC, 500XC-W

  • Corbin saddles (with very few exceptions) include Genuine Leather Seating to provide a luxurious look and feel....   don't let anybody tell you that vinyl is just as good! You wouldn't buy vinyl boots would you?

  • Warning: Heater elements (when available) should never be installed in motorcycle seats that will be used by riders that cannot sense heat. This could create a hazardous condition.


Corbin products are designed to fit very close to your bike for a clean look. Due to this, other accessories or options can inhibit proper fit. As an example: Tank Consoles (dashes), ignition modules, exhaust systems, sissy bars, etc. If you have accessories installed on your bike, please let us know so we can verify the fit for you.

Saddle Warranty

Basepan, foam and hardware of the Corbin saddle is warranted to the original owner for life. Cover materials, Heaters and workmanship are warranted for one year. Product will only be authorized to be shipped back, freight pre-paid, for refining of shape or to replace/rectify defective parts. In cases where the rework requires a new cover, a recover charge will be applied. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization number (RMA).

Fiberglass Warranty

Structural integrity of Corbin fiberglass components are warranted to the original owner for life. Finish and paint are warranted against manufacturing defect for one year. Damage to product and / or painted surfaces from outside forces or misuse is specifically not covered under warranty. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization (RMA) number.
A note about paint color matching, Please Read

Export Sales

USA pricing shown. When products are shipped throughout the world, you will see higher prices because of freight, customs, duty and applicable taxes. Please consider these costs when purchasing Corbin products outside the USA. If ordering direct from Corbin, we will compute freight charges and add them to the order. BUYER will be responsible for customs, taxes, duty or other charges.

Our Dual Sport seat allows freedom of movement for the rider from front to back while providing significantly wider, contoured seating towards the middle and rear. This allows for aggressive riding AND comfort. As much as we hate to sound cliche'... it's Form AND Function!

Corbin's seating platform is neutralized to curb sliding in the saddle which eliminates fatigue over the long run. Inside the saddle we use a proprietary foam material called Comfort Cell that provides a firm, resilient ride that lasts. Developed especially for Corbin and our patented manufacturing technique, Comfort Cell can be cast to the density best suited for each saddle design. This allows us to make each saddle provide just the right amount of support... too soft and you feel like you're bouncing off the basepan, too hard and you may as well be sitting on the fender.

Casting our foam allows us to design complex shapes that conform to the contours of your body. We call this "ergonomic shaping" and it gives you more square inches of body contact for better weight dispersion. This shaping also helps to eliminate the centralized pressure created by the narrow stock seat and soft foam as it compresses. Towards the nose we keep the shape low to aid ground reach.

On top we use only the highest grade of weather resistant materials for durability and long life. We dressed up this model with Carbon-Fiber style leather seating and asphalt vinyl side panels for contrast with a orange welt. Cover is completely hand sewn and riveted to our rigid Fibertech basepan. Naturally, custom material selection is available at no extra charge. Saddle installs like stock and rides on rubber bumpers to protect your bodywork and chassis.

We offer two models of this great saddle design; One works with the stock tank on all of the XC models listed, while the other is designed specifically for the 20 Liter Acerbis fuel tank available for the 350 and 500 models. Providing all of the same ergonomic perfection as the standard model, but we've modified the nose to fit the larger capacity tank. Now you'll have all the comfort you need to go out and burn those 5 gallons!

The Corbin seat mounts in the front with a tongue and a single bolt under the fender.


Unique Technology

The design and manufacture of Corbin products is so unique that Mike Corbin himself holds more than 60 United States Patents! From the process itself to new innovations like the Corbin Glovebox, you can count on highly functional and unique products that work. Corbin products are manufactured under one or more of the following US Patents: 6,848,156 B2; 6,729,516 B2; D 489,540S; 6,655,740 B1; 6,422,648 B1; 5,544,937; 5,608,957; 4,953,911; D545,073S & 6,971,714 B1.

Fibertech™ Basepan

A purpose built, hybrid material that provides a firm foundation to support the carefully designed ergonomics of the Corbin saddle. Provides a precision fit to every arc and contour of the machine and rides on rubber bumpers to protect your paint. We always design our basepans as flat as possible so bumps or odd shapes don't telegraph through the foam to your body. Click on the button at left to learn more...

Comfort Cell® Foam

The heart of the Corbin saddle! Our exclusive, purpose built foam material, called Comfort Cell, was created to provide a firm, resilient ride that doesn't break down. This means it will support you for long days on the road. Over time, Comfort Cell will break in to provide a personalized fit to your posture and even greater comfort!

Ergonomic Shaping

A major part of the design criteria of the Corbin saddle is the Ergonomic shape. This means the saddle's foam shape is designed to emulate the curves of the human body. This provides more square inches of body contact and helps to eliminate hot spots. This shaping also neutralizes the seating platform to help curb sliding in the saddle which reduces fatigue. In a nutshell... more comfort for a longer ride! Just click the button at left for an animation that shows how it works.

Patented Manufacturing Technology

Always an innovator, Mike Corbin invented Integrated Molding technology which is now the process by which all Corbin saddles are made. This process allows extremely tight tolerances and creates a chemical bond between the foam and base material. To see what this is all about, just click the button for More Info

Genuine Leather

We use leather in all panels of the seat that contact your body. This provides a luxurious ride that breathes with your body. Leather will also break in along with the foam shape to support the personalized fit. Available in a wide range of textures and styles to suit your taste. For more information about leather seating just click away.

Write a review

Note: HTML is not translated!
    Bad           Good

  • Views: 660
  • Product Code: KTM-5-EXC-13-ST
  • Availability: 10
  • £0.00
  • Ex Tax: £0.00

    Click the "Design It" button to explore. You will be taken to our visual design tool where you can experiment and share it with your friends, add it to your shopping cart or just play around for a bit.

Available Options

Tags: Dual Sport saddle for 2012 - 2016 KTM 250, 300, 350, 450 & 500 XC models, KTM-5-EXC-13-ST, 2012-2016 XC / EXC